Gilderflukeco DMX-512, Serial, and MIDI Output Smart Bricks Bedienungsanleitung Seite 23
- Seite / 48
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
BS-Serial in Intelix Mode
For a BS-Serial in Intelix mode, the menu will appear as follows. If an Eprom is found, the size of the first
show is displayed at the top of the screen. If no Eprom is found, the Ônot foundÕ will appear in the place of
the show size:
-Gilderfluke & Company - Serial Output Smart Brick - v1.05 - copyright 1999 DCM-
EPROM: 123 channels @ 30 FPS / first show is 12345 frames long
a) 1st address in Eprom- _10
b) baud rate- 38.4Kbaud
c) DMX Rx checksums- yes
d) sequencer enabled- yes
e) frame rate divided/2- no
f) numbering system- decimal
g) VT-52 display- yes
h) operating mode- Intelix
i) monitor channel- _10
j) Intelix strings....
l) string trigger channel- _11
m) edit strings....
o) reload defaults....
r) download configuration....
Enter Command-
a) First Addressed in Eprom: Any DMX-512 data that is sent to the BS-Serial will be passed
through at the same address at which it was received. This command is used to offset the
data from the on-board Eproms to match the addresses that were used when you were pro-
gramming. As an example, if the outputs you are using start at 10, then you need to create
the Eprom files set starting with a ÔstartÕ of 10 in the PC¥MACs program. When playing back
from the BS-Serial, the data will need to be offset to Ô10Õ so that the channels are reproduced
at the same locations where they were when you were programming.
b) Baud Rate: This command sets the speed at which serial data is sent out of the BS-SerialÕs seri-
al port when the card isnÕt in configuration mode. The baud rates available on the BS-Serial
are:
1) MIDI baud rate (31,250 baud)
2) 2400 baud
3) 4800 baud
4) 9600 baud
5) 19.2 KBaud
6) 38.4 KBaud
7) 57.6 KBaud
8) 115.2 KBaud
The baud rate must be set to match the device you are trying to talk to. The highest speed
supported by the Intelix Matrix Mixers is 38.4 KBaud. This is the speed that should be used when
in Intelix mode. No matter what baud rate you select here, the configuration mode will always
run at 9600 baud.
c) DMX Rx Checksum: This toggle is used to enable and disable the error checking in data re-
ceived through the DMX-512 data input. Without it, the BS-Serial Smart Brick won't be able to
recognize errors in the incoming data, and may update the outputs with this bad data. It
should be left ON whenever running from a PC¥MACs or other DMX-512 source that supports
this checksum. All Gilderfluke & Company send this checksum. If this toggle is ON and the
GILDERFLUKE & C
O
.¥ 205 S. FLOWER ST. ¥ BURBANK, CA 91502 ¥ 818/840-9484 ¥ 800/776-5972 ¥ FAX 818/840-9485
23 of 48
- Printed March 24, 2000 1
- GILDERFLUKE & C 1
- This page left blank 2
- Overview 7
- ONE START BIT 9
- EIGHT DATA BITS 9
- ONE STOP BIT 9
- ILDERFLUKE & C 10
- BackPlane Connections: 11
- Animation Data Eproms: 13
- 27C010 131,072 14
- 27C020 262,144 14
- 27C040 524,288 14
- 27C080 1,048,576 14
- BS-DMX-Tx 17
- BS-Serial in MIDI Mode 18
- BS-Serial in Intelix Mode 23
- BS-Serial in Orpan Modes 32
- BS-Serial in Moog Modes 36
- 47 of 48 47
Verwandte Produkte und Handbücher für Audio Gilderflukeco DMX-512, Serial, and MIDI Output Smart Bricks
(75 Seiten)Samsung SC6580 manuales
Manuales del propietario y guías del usuario para Reproductores de cd Samsung SC6580.
Ofrecemos manuales en pdf Samsung SC6580 para descargar gratis por tipos de documentos:
Kommentare zu diesen Handbüchern